Designed to fit

Universal Fitment

For questions about installing a water/methanol kit in your car, please contact us at info@flat6motorsports.com

Product Details

Stage 1

The Snow Performance Stage 1 Boost Cooler® water-methanol injection kit is available for all forced induction applications (supercharged/turbocharged). Operation of this Snow Performance methanol kit is simple and reliable: the system starts injecting when the boost switch reaches the user-adjustable point and injects a fixed amount of fluid through the nozzle until boost goes below the set switch point. Proven to deliver 30-70 HP increases to all forced induction applications! This makes it a good choice for low to medium boost setups (1-15 PSI) looking for an octane enhancement and cooler intake charge. Activation can also be set up through any other user-chosen switch, such as a full throttle switch, nitrous switch, etc. Purchase this water-methanol injection kit today.

Kit Includes:

300 PSI UHO (Ultra High Output) Pump
3 Quart Reservoir
All Tubing Necessary for Installation 10' ¼ Inch High Temp Nylon Tubing 18" High pressure Boost Line 3' (Black) Wire Loom
Boost Switch (1-15 PSI)
Pig Tail Harness
Level Switch Upgrade
1 Nozzle Holder/Check Valve Combo
3 Hyper-Sonic™ Nozzles (175, 375, 625 ml/min)
Required Hardware Needed For Installation
Comprehensive Instructions to Install on Any Forced Induction Vehicle
Snow Performance 1-Year Warranty

Stage 2

Unlock 50-80HP on your boosted vehicle while decreasing your air temps by up to 150 degrees! The all new Snow Performance Stage 2 Boost Cooler® water-methanol injection system comes fully revamped in 2015 for all boosted (turbocharged/supercharged) vehicles and uses a progressive gauge style controller that proportionally injects more or less according to boost pressure. Start and full points are adjustable for engagement and delivery curve to match what the engine requires. Proportionally injecting according to boost pressure gives an accurate delivery of water-methanol and allows cooling and performance improvements over a wide range for improved drivability. Taking it one step further, the Stage 2 has the ability to progressively command 2 Hyper-Sonic™ Nozzles independently of one another. This sophisticated dual stage injection management yields the highest increases in HP and cooling along all stages of the engine allowing you to greatly increase the boost & timing of your vehicle safely. Proven to deliver 50-80 HP and cool inlet temps up to 150 degrees! The VC-50 comes with a dual 7 color OLED screen and displays boost, percentage of injection, low level, and secondary nozzle activation directly on the screen. Complete with our industry leading Snow Performance 300 PSI UHO pump and Hypersonic Nozzles, the Stage 2 promises to deliver the best atomization and power available for your boosted vehicle.

Kit Includes:

300 PSI UHO (Ultra High Output) Pump
3 Quart Reservoir
All Tubing Necessary for Installation 10' ¼ Inch High Temp Nylon Tubing 18" High pressure Boost Line 3' (Black) Wire Loom
VC-20 or The New Generation VC-50 Controller
Pigtail Harness
2 1/16 Gauge Pod
Level Switch Upgrade
1 Nozzle Holder/Check Valve Combo
3 Hyper-Sonic™ Nozzles (175, 375, 625 ml/min) For Applications up to 1,000 HP
Required Hardware Needed For Installation
Comprehensive Instructions to Install on Any Forced Induction Vehicle
Snow Performance 1-Year Warranty

Stage 3

The Snow Performance Stage 3 Boost Cooler® is the most advanced water-methanol injection system for your EFI (electronic fuel injected) and forced induction (turbocharged/supercharged) vehicle. The Stage 3 creates a 2D injection map based off boost and fuel injector pulse width to deliver the most accurate and tunable water-meth delivery on the market. Taking it one step further the Stage 3 will control 2 Hyper-Sonic™ Nozzles independently of one another to solidly the exact amount of water-methanol is provided at all rpm ranges of the engine. This 2D map injection and dual stage technology translates into the most accurate injection curve and tuneability of any water-methanol system giving 50-110 HP gains and up to 150 degree reduction in air temps! Tie this in with the industry leading Snow Performance 300 PSI UHO pump, Hypersonic Nozzles™, and terminated weather tight OEM harnessed wiring connections and the Stage 3 promises to be the easiest and most effective water-methanol system on the market for your EFI and boosted vehicle.

Kit includes:

300 PSI UHO (Ultra High Output) Pump
3 Qt Reservoir
All Tubing Necessary for Installation 10' ¼ Inch High Temp Nylon Tubing 18" High pressure Boost Line
Terminated Digital Variable Mapping Controller
Terminated Plug&Play Wire Harness
Power Solenoid Upgrade
Level Switch Upgrade
2 Nozzle Holder/Check Valve Combo
3 Hyper-Sonic™ Nozzles
Required Hardware Needed For Installation
Comprehensive Instructions to Install on any EFI/Boosted Vehicle
Snow Performance 1-Year Warranty

Video

About Snow Performance

The Water-Methanol Injection Experts.

As the largest and oldest water-methanol injection company we bring experience and insight to all aspects of water-methanol injection. It is our promise and passion to deliver a state of the art water-methanol injection experience to our customers through quality components (Made in the USA), honest marketing, expert technical support for all water-meth users regardless if our system, no questions asked customer service, and offer products that deliver an outstanding value to all Snow Performance customers regardless of location. Our vision is for all to benefit with this great technology and give quality injection systems that simple perform. We love what we do and would like to invite you to share in the Snow Performance promise of quality, value, and performance.

FREE SHIPPING / $299+

Filters

Model

Category

Sub Category

Brand

Snow Performance Forced Induction Water/Methanol Injection Kit

ABOUT

CONTACT

TECHNICAL

FOLLOW US